• kylian0087@lemmy.world
    link
    fedilink
    English
    arrow-up
    5
    ·
    edit-2
    1 year ago

    Carefull using PLA. PC components can get HOT and potentialy melt the PLA.

    Other then that. It looks very good and clean. Do you happen to share the stls?

    • rambos@lemmy.worldOP
      link
      fedilink
      English
      arrow-up
      3
      ·
      1 year ago

      Sure thing

      https://www.printables.com/model/486506-3d-print-pc

      I was also worried about that, but for this PC its only sun that can melt it haha. But yeah it would be better to print with petg or abs Cpu temp never goes above 45C lol. Usually at 35 and case fans are not even spinning. Also mbo is “raised” 10 mm from back wall if that make sense.

    • Macaroni Love@lemmy.ca
      link
      fedilink
      English
      arrow-up
      3
      ·
      1 year ago

      I printed a case for a small PC that I user as a home server 3 years ago, and I used the cheapest PLA out there. No warping, nothing broke. It is cooled by a single 80mm.

      As long as there’s enough airflow to prevent the PLA from actually heating up, it will be fine.

    • LanyrdSkynrd@lemmy.world
      link
      fedilink
      English
      arrow-up
      2
      ·
      1 year ago

      I’ve also had problems with PLA prints delaminating and becoming brittle over time, especially if it’s being flexed or exposed to sunlight. Some PLA’s are worse than others with this, though.

      I use PETG for anything I want to last a long time.

      • rambos@lemmy.worldOP
        link
        fedilink
        English
        arrow-up
        2
        ·
        1 year ago

        Yeah, but I only had these 2 rolls of PLA. Spent like 800-900 g of each. If it brakes ill make the another one in petg

        • solarbird@kbin.social
          link
          fedilink
          arrow-up
          1
          ·
          1 year ago

          If you’re willing to get into annealing, I’ve had good service from annealed HTPLA in high temperature/humidity and even overpressure environments. I’m three years into a build that gets multiple hours of use in such conditions a week and it’s held up fine. There have been other problems, but nothing related to bad behaviour out of the HTPLA.

  • ironcrotch@aussie.zone
    link
    fedilink
    English
    arrow-up
    2
    ·
    1 year ago

    Out of all things a PC case is something I never considered to print. Looks great! Might give this a try for a SFFPC.

    • rambos@lemmy.worldOP
      link
      fedilink
      English
      arrow-up
      2
      arrow-down
      1
      ·
      1 year ago

      It’s hard to find anything if you don’t want to spend big $$. Good enough reason to sink loads of time hehe

    • rambos@lemmy.worldOP
      link
      fedilink
      English
      arrow-up
      2
      ·
      1 year ago

      Im not sure, dont have wifi on this board, but was planning to get zigbee dongle or something like that for homeassistant in near future.

      At one point I had a PC connected to a wifi with no case at all, but dont know much about that RF shielding tbh

      • chunkystyles@sopuli.xyz
        link
        fedilink
        English
        arrow-up
        1
        ·
        edit-2
        1 year ago

        ZigBee is so good. The only downside is it’s sometimes hard to find devices. They’ll make a Z-Wave device, but not ZigBee.

  • alien@lemm.ee
    link
    fedilink
    English
    arrow-up
    1
    ·
    1 year ago

    I actually thought this was a playstation at the first glance haha. I can’t tell how mini it is… need something for scale… a banana might help!

    • rambos@lemmy.worldOP
      link
      fedilink
      English
      arrow-up
      2
      ·
      1 year ago

      288x207x343 mm (WxDxH)

      Its small for ATX motherboard, but big enough that I had to splir the case in 4 peaces to fit my printer. Ill get banana next time lol

  • TooL@kbin.social
    link
    fedilink
    arrow-up
    1
    ·
    edit-2
    1 year ago

    Combining my two favorite money sinks/hobbies.

    So… What are the specs of the PC?

    Edit: I have no idea how to do strikethrough text here.

    • rambos@lemmy.worldOP
      link
      fedilink
      English
      arrow-up
      3
      ·
      1 year ago
      MBO: MSI Z270-A PRO
      CPU: Intel G3930
      RAM: DDR4 8GB
      PSU: Corsair RM550X
      FAN: 2x Arctic F12
      3x SSD for OS and storage
      

      Most of components were laying around and I wanted to build low power server. Its pulling 20-30W from the wall and its more than enough for my needs (media server, home assistant and some other lightweight apps), but I might need to upgrade RAM if I continue adding services 🙃

          • TooL@kbin.social
            link
            fedilink
            arrow-up
            1
            ·
            1 year ago

            Really? With just the CPU? That’s actually pretty impressive! I added a dedicated GPU for mine because the CPU was not cutting.

            • rambos@lemmy.worldOP
              link
              fedilink
              English
              arrow-up
              2
              ·
              1 year ago

              I think its called quicksync. If processor supports that transcoding becomes easy task afaik